Huawei Quidway S3900 Series Скачать руководство пользователя страница 48

Страница: 48 / 95

Installation Manual
Quidway S3900 Series Ethernet Switches

Chapter 1 Product Overview

Huawei Technologies Proprietary

1-32

III. Attributes of the 10Base-T/100Base-TX Ethernet ports

Table 1-14

Attributes of the 10Base-T/100Base-TX Ethernet ports on the

S3928P-PWR-EI

Attribute

Description

Connector RJ-45

Number of ports

Rate

10/100 Mbps, half duplex/full duplex

MDI/MDI-X autosensing

PoE remote power supply

Standard

IEEE 802.3u

IEEE 802.3af

Transmission segment over
the selected medium

100 m (328.08 ft) over the category-5 unshielded
twisted pair (UTP) cable

IV. Attributes to the 1000 Mbps SFP ports

Depending on your needs, the S3928P-PWR-EI can provide four 1000 Mbps SFP ports
(optical or electrical) on its front panel.

Note:

SFP module does not support PoE.

SFP modules allow for great flexibility because they are hot swappable and user
configurable.

For available SFP modules, see Table 1-6.

Note:

The available 1000 Mbps SFP modules are subject to changes. For information on the
latest module options, contact your sales agent.

V. Console port

The S3928P-PWR-EI provides one EIA/TIA-232 compliant Console port for local or
remote switch configuration. For its attributes, see Table 1-4.

Содержание Quidway S3900 Series
































































































Результаты поиска

Содержание Quidway S3900 Series

Отзывы:

Бренды по названию

Популярные бренды

Huawei Quidway S3900 Series, Руководство по установке

Результаты поиска

Содержание Quidway S3900 Series

Отзывы:

Бренды по названию

Популярные бренды