manualshive.com logo in svg

Huawei Quidway S3900 Series, Руководство по установке

Поделиться
Скачать
Huawei Quidway S3900 Series Скачать руководство пользователя страница 2

3.1 Mounting the Switch in a Rack or on a Tabletop

3-1

....................................

3.1.1 Rack-Mounting the Switch

3-1

.............................................................

3.1.2 Mounting the Switch on a Tabletop/Workbench

3-2

............................

3.2 Connecting the Power Cord and the Ground Wire

3-2

.................................

3.2.1 Connecting the AC-Input Power Cord

3-2

............................................

3.2.2 Connecting the DC-Input Power Cord

3-3

...........................................

3.2.3 Connecting the Ground Wire

3-4

.........................................................

3.2.4 Multi-power Input

3-7

...........................................................................

3.3 Connecting the Switch to a Console Terminal

3-7

.......................................

3.3.1 Console Cable

3-7

...............................................................................

3.3.2 Connecting the Console Cable

3-8

......................................................

3.4 Verifying Installation

3-8

...............................................................................

Chapter 4 Starting up the Switch at the Initial Boot

4-1

.....................................

4.1 Setting up a Configuration Environment

4-1

.................................................

4.2 Connecting the Console Cable

4-1

...............................................................

4.3 Setting Terminal Parameters

4-1

..................................................................

4.4 Booting the Switch

4-4

..................................................................................

4.4.1 Verifying Installation before Power-up

4-4

...........................................

4.4.2 Powering up the Switch

4-4

.................................................................

Chapter 5 Loading Boot ROM and Host Software

5-1

........................................

5.1 Introduction to Loading Approaches

5-1

.......................................................

5.2 File attribute in Boot ROM

5-1

......................................................................

5.2.1 Introduction to File Attribute

5-1

...........................................................

5.2.2 Impact of File Attributes on Downloading and Booting

5-2

..................

5.2.3 Setting the Attribute of a File

5-3

..........................................................

5.3 Loading Software Locally

5-4

.......................................................................

5.3.1 Boot Menu

5-5

......................................................................................

5.3.2 Loading Software from Console Port Using XModem

5-6

...................

5.3.3 Loading Software from an Ethernet Port Using TFTP

5-11

...................

5.3.4 Loading Software from an Ethernet Port Using FTP

5-12

......................

5.4 Loading Software Remotely

5-13

...................................................................

5.4.1 Loading Software Remotely Using FTP

5-14

.........................................

5.4.2 Loading Software Remotely Using TFTP

5-15

.......................................

Chapter 6 Maintenance and Troubleshooting

6-1

...............................................

6.1 Dealing with Loading Failures

6-1

................................................................

6.2 Dealing with Password Loss

6-1

..................................................................

6.2.1 Dealing with User Password Loss

6-1

.................................................

6.2.2 Recovering the Boot ROM Password

6-2

............................................

6.3 Dealing with Power System Failures

6-2

......................................................

Содержание Quidway S3900 Series
































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды