manualshive.com logo in svg

Huawei Quidway S3900 Series, Руководство по установке

Поделиться
Скачать
Huawei Quidway S3900 Series Скачать руководство пользователя страница 41

Installation Manual 
Quidway S3900 Series Ethernet Switches 

Chapter 1  Product Overview

 

Huawei Technologies Proprietary 

1-25 

LED 

Mark 

Color 

Indicates 

ON 

The port is connected, and the 
device is in an IRF loop fabric. 

Green

Flash 

Data is being received/sent on 
the port 

ON 

The port is connected, and the 
device is in an IRF chain fabric.

Yellow

Flash 

Data is being received/sent on 
the port 

Flashing green 
(3 Hz) 

Fabricing fault occurs. 

Flashing yellow 
(3 Hz) 

The port fails POST. 

Speed 

OFF 

The port is not connected. 

ON 

The port is operating in full 
duplex mode 

Green

Flash 

Data is being received/sent on 
the port 

Flashing yellow 
(3 Hz) 

The port fails POST. 

Duplex 

OFF 

The port is not connected. 

OFF 

No data is being received/sent

10/100/1
000Base
-T Fabric 
port LED

 

PoE 

Flashing yellow 
(3 Hz) 

The port fails POST. 

 

III. Attributes to the 100 Mbps SFP ports 

Depending on your needs, the S3928F-EI can provide up to 24 x 100 Mbps SFP optical 
ports (numbered from 1 to 24) on its front panel. 

SFP modules allow for great flexibility because they are hot swappable and user 
configurable. 

For available SFP modules, see Table 1-12: 

Содержание Quidway S3900 Series
































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды