manualshive.com logo in svg

Huawei Quidway S3900 Series, Руководство по установке

Поделиться
Скачать
Huawei Quidway S3900 Series Скачать руководство пользователя страница 75

Installation Manual 
Quidway S3900 Series Ethernet Switches 

Chapter 5  Loading Boot ROM and Host Software

 

Huawei Technologies Proprietary  

5-1

 

Chapter 5  Loading Boot ROM and Host Software 

Switch software loading through serial ports in the past is time consuming and cannot 
be operated remotely. To address these problems, TFTP and FTP are used to allow 
software and file downloading through Ethernet ports. The following subsections 
describe how to load software and files in these two approaches. 

5.1  Introduction to Loading Approaches 

To load software remotely, use FTP or TFTP. 

To load software at the local, use XModem at the Console port or TFTP/FTP at an 
Ethernet port. 

 

 

  Note: 

Ensure that the Boot ROM and host software versions that you download can work with 
each other. 

 

5.2  File attribute in Boot ROM 

5.2.1  Introduction to File Attribute 

In Boot ROM, application files, configuration files, and Web files support three kinds of 
attributes: main, backup, and none, which are described in Table 5-1. 

Table 5-1 

File Attribute 

Attribute 

Usage 

Feature 

Identification

main 

Indicates the main boot 
file, which is used by a 
device to boot. 

Only one application 
file, one configuration 
file, and one Web file in 
the Flash can have the 
main attribute. 

(*) 

backup 

Indicates a boot file with 
the backup attribute. 
When a device cannot 
boot with the main boot 
file, it will use the backup 
boot file to boot. 

Only one application 
file, one configuration 
file, and one Web file in 
the Flash can have the 
backup attribute. 

(b) 

Содержание Quidway S3900 Series
































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды