manualshive.com logo in svg

Huawei Quidway S3900 Series, Руководство по установке

Поделиться
Скачать
Huawei Quidway S3900 Series Скачать руководство пользователя страница 35

Installation Manual 
Quidway S3900 Series Ethernet Switches 

Chapter 1  Product Overview

 

Huawei Technologies Proprietary 

1-19 

LED 

Mark  

Color 

Indicates 

ON 

The port is connected, and the 
device is in an IRF loop fabric. 

Green

Flash

Data is being received/sent on 
the port. 

ON 

The port is connected and the 
device is in an IRF chain fabric. 

Yellow

Flash

Data is being received/sent on 
the port. 

Flashing green 
(3Hz) 

Fabricing fault occurs. 

Flashing yellow 
(3 Hz) 

The port fails to pass POST. 

Speed 

OFF 

The port is not connected. 

ON 

The port is in full duplex mode 
and is fabriced. 

Green

Flash

Data is being received/sent on 
the port. 

Flashing yellow 
(3 Hz) 

The port fails to pass POST. 

Duplex 

OFF 

The port is not connected. 

Flashing yellow 
(3 Hz) 

The port fails to pass POST. 

1000Bas
e SFP 
Fabric 
port LED

 

PoE 
mode 

OFF –– 

 

III. Attributes of the 10Base-T/100Base-TX Ethernet ports 

See Table 1-3. 

IV. Console port 

The S3928P-EI provides one EIA/TIA-232 compliant Console port for local or remote 
switch configuration. For its attributes, see Table 1-4. 

V. Attributes of the 1000 Mbps SFP ports 

Depending on your needs, the S3928P-EI can provide up to four SFP ports (optical or 
electrical) on its front panel. 

SFP modules allow for great flexibility because they are hot swappable and user 
configurable. 

For available SFP modules, see Table 1-6. 

 

Содержание Quidway S3900 Series
































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды