Huawei IDS1000 Скачать руководство пользователя страница 64

Страница: 64 / 67

IDS1000 Container Data Center
User Manual

8 Emergency Operation

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

8.2 Single Fire Alarm

Prerequisites

A single fire alarm is generated in the data center.

The emergency operations described in this section are for reference only.

If a fire alarm is generated, determine whether to extinguish the fire or leave the area
immediately based on actual situation and contact the personnel on duty or local fire station.

Procedure

Step 1

Locate the fire alarm area based on the alarm information.

Step 2

Go to the area with necessary personal protective equipment (PPE) and communications
devices.

Do not enter the fire alarm area without determining the severity and impact of the fire.

Step 3

Observe the gas release indicator to check whether gas is released to extinguish the fire.

If gas is released, contact Huawei technical support.

If gas is not released, go to the next step.

Step 4

Check whether there are alarms on the gas fire extinguishing controllers outside the container.



If the gas fire extinguishing controllers reports a single fire alarm but the VESDA does
not generate any alarm, go to

Step 5



If the gas fire extinguishing controllers reports a single fire alarm (smoke alarm) and the
VESDA reports an alarm, go to

Step 5



If the gas fire extinguishing controllers reports a single fire alarm (temperature alarm)
and the VESDA reports an alarm, go to

8.3 Composite Fire Alarm



If the gas fire extinguishing controllers reports a composite fire alarm, go to

8.3

Composite Fire Alarm

Step 5

Open the door of the container and check whether a fire has broken out.

Содержание IDS1000




































































Результаты поиска

Содержание IDS1000

Отзывы:

Похожие инструкции для IDS1000

Бренды по названию

Популярные бренды

Huawei IDS1000, Руководство пользователя

Результаты поиска

Содержание IDS1000

Отзывы:

Похожие инструкции для IDS1000

Бренды по названию

Популярные бренды