Huawei IDS1000 Скачать руководство пользователя страница 63

Страница: 63 / 67

IDS1000 Container Data Center
User Manual

8 Emergency Operation

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

If gas is released, contact Huawei technical support.

If gas is not released, go to the next step.

Step 4

Check whether there are alarms on the gas fire extinguishing controllers outside the container.



N => Go to

Step 5



Y => If a smoke alarm is generated, go to

8.2 Single Fire Alarm



Y => If a temperature alarm is generated, go to

8.3 Composite Fire Alarm



Y => If a complex alarm is generated, go to

8.3 Composite Fire Alarm

Step 5

Open the door of the container and check whether a fire has broken out.

Open the container door a crack and check whether a fire has broken out in the container. If a
fire has broken out, close the door immediately and press the emergency start switch to put
out the fire. If there is no fire, go to

Step 6

Step 6

Determine the alarm severity based on the documents delivered with the VESDA.

Step 7

Check whether there is obvious smoke or combustible in the container.

N => Go to

Step 8

Y => Go to

Step 9

Step 8

Check for faults of the power supply system and cooling system.

If no fault is found in the container data center components, rectify the fault by following the
instructions in

6.7 VESDA Fault

Step 9

Use a carbon dioxide fire extinguisher to spray the combustibles.

Step 10

Rapidly power off the devices in the smoke area or near the combustibles and switch off the
circuit breakers.

Step 11

After the fire alarm is cleared, report the event to the management department of the data
center and contact Huawei technical support.

----End

Follow-up Procedure

Analyze the cause of the fault, and work out and record the preventive measures.

Содержание IDS1000




































































Результаты поиска

Содержание IDS1000

Отзывы:

Похожие инструкции для IDS1000

Бренды по названию

Популярные бренды

Huawei IDS1000, Руководство пользователя

Результаты поиска

Содержание IDS1000

Отзывы:

Похожие инструкции для IDS1000

Бренды по названию

Популярные бренды