Huawei IDS1000 Скачать руководство пользователя страница 22

Страница: 22 / 67

IDS1000 Container Data Center
User Manual

3 Power-On Commissioning

Issue 01 (2014-3-15)

Huawei Proprietary and Confidential

Figure 3-6

Setting the power-on delay for the solenoid valve from 25s to 30s

The factory setting for the solenoid valve power-on delay is 30s, as shown in

Figure 3-7

Figure 3-7

Setting the initial power-on delay for the solenoid valve

Step 5

Set the gas extinguishing controller time display.

Open the controller panel and calibrate time from the rear of the display panel.

There are three buttons and one light emitting diode on the rear of the panel. The three buttons are

Switchover S12

Former plus S11

, and

Later plus S10

, respectively, which are used to calibrate time.

Former plus

means plus 1 for the first two values of the nixie tube, and

Later plus

means

plus 1 for the last two values of the nixie tube. The adjustment methods are as follows:

Press

Switchover S12

, and the H11 indicator lights up, indicating that the time is being

calibrated. The nixie tube displays the year in the format of

. Press

Later plus S10

add the value, which ranges from 1 to 60.

Then press

Switchover S12

, and the nixie tube displays the month and day in the format

??.??

Press

Former plus S11

to adjust the month, which ranges from 1 to 12, and then press

Later plus S10

to adjust the date, which ranges from 1 to 31.

Press

Switchover S12

again to display hour and minute, which is in the format of

??:??

Press

Former plus S11

to adjust the month, which ranges from 1 to 23. Then press

Later plus S10

to adjust the day, which ranges from 0 to 59.

Press

Switchover S12

again to finish the time setting. The indicator H11 lights off. The

nixie tube displays the hour and minute.

Содержание IDS1000




































































Результаты поиска

Содержание IDS1000

Отзывы:

Похожие инструкции для IDS1000

Бренды по названию

Популярные бренды

Huawei IDS1000, Руководство пользователя

Результаты поиска

Содержание IDS1000

Отзывы:

Похожие инструкции для IDS1000

Бренды по названию

Популярные бренды