HP ProLiant SL160z - G6 Server Скачать руководство пользователя страница 74

Страница: 74 / 80

Diagnostic tools and Setup Utilities 74

Table 10

POST error message

601

Error: BMC Not Responding

040

Refresh timer test failed

048

Password check failed

00B

CMOS Memory Size Wrong

010

Floppy Controller Failure

00C

RAM R/W test failed

003

CMOS Battery Low

701

Insufficient Runtime space for MPS data.

System may operate in PIC or Non-MPS mode.

702

No enough APIC ID in range 0-0Fh can be assigned to IO APICs.

(Re-assigning CPUs' local APIC ID may solve this issue)

MPS Table is not built! System may operate in PIC or Non-MPS mode.

120

$A0CCMOS Cleared by Jumper. Restore the Jumper and Continue.

122

$A0CPassword Cleared By Jumper. Restore the Jumper and Continue.

POST Related Troubleshooting

Perform the following procedures when POST fails to run, displays error messages, or emits beep
codes.
If the POST failure is during a routine boot up, check the following:

•

All external cables and power cables should be firmly plugged in.

•

The power outlet to the server should be connected and works correctly.

•

The server and monitor are both turned on. The bicolour status LED indicator on the front panel

must be lit up green.

•

The monitor's contrast and brightness settings are correct.

•

All internal cables are properly connected and all boards firmly seated.

•

The processor is fully seated in its socket on the system board.

•

The cooler assembly is properly installed on top of the processor.

•

All memory modules are properly installed.

•

If you have installed a PCI accessory board, verify that the board is firmly seated and any

switches or jumpers on the board are properly set. Refer to the documentation provided with the

accessory board.

•

All internal cabling and connections are in their proper order.

•

If you have changed any switches on the system board, verify that each is properly set.

All manuals and user guides at all-guides.com

Содержание ProLiant SL160z - G6 Server

















































































Результаты поиска

Содержание ProLiant SL160z - G6 Server

Отзывы:

Похожие инструкции для ProLiant SL160z - G6 Server

Бренды по названию

Популярные бренды

HP ProLiant SL160z - G6 Server, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ProLiant SL160z - G6 Server

Отзывы:

Похожие инструкции для ProLiant SL160z - G6 Server

Бренды по названию

Популярные бренды