HP ProLiant SL160z - G6 Server Скачать руководство пользователя страница 68

Страница: 68 / 80

Diagnostic tools and Setup Utilities 68

•

Super IO Configuration

–You can use this screen to select options for the Super I/O settings. Use

the up and down <Arrow> keys to select an item. Use the <Plus> and <Minus> keys to change

the value of the selected option. The settings are described on the following pages.

•

USB Configuration

–These items control various USB devices. From the USB configuration screen,

press <Enter> to access the submenu for the USB BIOS Support. Use the up and down <Arrow>

keys to select an item. Use the <plus>and <minus> keys to change the value of the selected

option. The settings are described on the following pages.

•

PCI Configuration

--- You can use this screen to configure PCI Device such as Embedded VGA

Control, Embedded NIC.

•

PCI Express Configuration

–You can use this screen to configure PCI Device such as Embedded

VGA Control, Embedded NIC.

•

IPMI Configuration

–Select this option and press <Enter> to access the submenu. You can use the

submenu to view the contents of IPMI .A delay may be noticed when selecting IPMI. This is due

to the retrieval of sensor data .In the submenu, use the up and down <Arrow> keys to select an

item. Use the <Plus> and <Minus>keys to change the value of the selected option.

•

BIOS Serial Console Configuration

–Set this value to allow configuring the serial port.

•

Trusted Computing

–Configure settings related to trusted Computing innovations.

Figure 57

IPMI Configuration menu of the BIOS Setup Utility

•

Set LAN Configuration –

Select Set LAN Configuration in the left frame of the screen to go to the

submenu for that item. You can display a submenu about LAN options by highlighting it using

the<Arrow> keys. Set LAN Setup options are described in this section. The Set LAN BIOS Setup

screen is shown below (When you have a LO100 Device, this item will display).

•

SEL Configuration-

Select SEL Configuration in the left frame of the screen to go to the submenu

for that item. Then you can press Enter to enter its submenu. You can display a submenu about

SEL Configuration option by highlighting it using the <Arrow> keys.

•

Hardware Health Information–

Select Hardware Health Information in the left frame of the screen

and press<enter> to go to the submenu for that item. That will display CPU temperature, ambient

temperature, CPU fan speed, system fan speed, chassis fan speed. These items cannot be

changed by the user. It accords with the sense of the case. If there is LV CPU and no card in

slot1, then System Fan 6 Rotor 1 and System Fan 6 Rotor 2 no display.

All manuals and user guides at all-guides.com

Содержание ProLiant SL160z - G6 Server

















































































Результаты поиска

Содержание ProLiant SL160z - G6 Server

Отзывы:

Похожие инструкции для ProLiant SL160z - G6 Server

Бренды по названию

Популярные бренды

HP ProLiant SL160z - G6 Server, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ProLiant SL160z - G6 Server

Отзывы:

Похожие инструкции для ProLiant SL160z - G6 Server

Бренды по названию

Популярные бренды