HP ProLiant SL160z - G6 Server Скачать руководство пользователя страница 39

Страница: 39 / 80

Removal and Replacement Procedures 39

To apply the thermal grease compound:

Use a clean cloth dipped in rubbing alcohol to clean the contact surface on the heat sink and on
the new processor. Wipe the contact surfaces several times to make sure that no particles or dust
contaminants are evident.

Apply the thermal grease compound to the CPU contact surface.

CAUTION:

HP recommends using Shin-Etsu X-23-7783D thermal grease compound for your ProLiant

server.

Apply all the grease to the top of the processor in the following pattern to insure even
distribution.

Figure 16

Applying grease

CAUTION:

Applying too much grease creates a gap between the contact surfaces, significantly

reducing the ability of the heat sink to draw out heat. Installing the heat sink with excessive grease

can also cause the grease to spread over the processor pins or the system board base, which can

cause electrical shorts that damage the system.

To install the heat sink:

CAUTION:

To prevent overheating or a possible system crash, use only a heat sink model specified

for the HP ProLiant SL160z G6 server.

Put the heat sink frame on the CPU socket.

Properly align the heat sink mounting pins to the system board mounting holes.

Tighten the mounting pins clockwise to secure the heat sink connection to the system board.

CAUTION:

To prevent the heat sink from tilting to one side during installation and removal

procedures, use a diagonally opposite pattern (an “X” pattern) when loosening and tightening the

two spring-loaded screws. Do not over tighten the heat sink’s spring-loaded screws to prevent them

from breaking off. A maximum torque of 4 in-Ib is set for the system.

All manuals and user guides at all-guides.com

Содержание ProLiant SL160z - G6 Server

















































































Результаты поиска

Содержание ProLiant SL160z - G6 Server

Отзывы:

Похожие инструкции для ProLiant SL160z - G6 Server

Бренды по названию

Популярные бренды

HP ProLiant SL160z - G6 Server, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ProLiant SL160z - G6 Server

Отзывы:

Похожие инструкции для ProLiant SL160z - G6 Server

Бренды по названию

Популярные бренды