HP ProLiant SL160z - G6 Server Скачать руководство пользователя страница 49

Страница: 49 / 80

Removal and Replacement Procedures 49

Figure 34

System battery location

WARNING:

Note the following reminders when replacing the system battery:

•

Replace the battery with the same type as the battery recommended by HP. Use of another battery may
present a risk of fire or explosion.

•

A risk of fire and chemical burn exists if the battery is not handled properly. Do not disassemble, crush,

puncture, or short external contacts, or expose the battery to temperatures higher than 60°C (140°F).

•

Do not dispose of used battery in water or fire. Dispose of used batteries according to manufacturer's
instructions.

CAUTION:

Loss of BIOS settings occurs when the battery is removed. You must reconfigure BIOS

settings whenever you replace the battery.

NOTE:

If the server no longer automatically displays the correct date and time, you may need to

replace the system battery. Under normal usage, battery life is five to ten years.

To replace the system battery:

To release the battery from its holder, squeeze the metal clamp that extends above top of the
battery. When the battery pops up, lift it out.

To insert the new battery, slide one edge of the replacement battery under the holder’s lip with
the positive side facing the metal clamp. Push the other edge down until the clamp snaps over

the top of the battery.

All manuals and user guides at all-guides.com

Содержание ProLiant SL160z - G6 Server

















































































Результаты поиска

Содержание ProLiant SL160z - G6 Server

Отзывы:

Похожие инструкции для ProLiant SL160z - G6 Server

Бренды по названию

Популярные бренды

HP ProLiant SL160z - G6 Server, Руководство по техническому обслуживанию и ремонту

Результаты поиска

Содержание ProLiant SL160z - G6 Server

Отзывы:

Похожие инструкции для ProLiant SL160z - G6 Server

Бренды по названию

Популярные бренды