HP Kayak XU 03xx Скачать руководство пользователя страница 3

Страница: 3 / 30

English

HP Kayak XU 03xx PC Workstation — Installing Accessories In Your HP PC Workstation

Removing and Replacing the Cover

WARNING

For your safety, never remove the PC Workstation’s cover without first
removing the power cord from the power outlet, and any connection to
a telecommunications network. Always replace the cover on the
PC Workstation before switching it on again.

Removing the Cover

Switch off the display and computer.

Disconnect all power cables and any telecommunications cables.

If necessary, unlock the cover using the key on the back panel.

Lift the two latches on the front sides of the computer upwards.

Grasp the cover on the sides at the back of the computer and slide
it forwards and off the computer.

Step 4

Step 5

03xx-i~1.fm Page 3 Tuesday, February 16, 1999 10:15 AM

Содержание Kayak XU 03xx































Результаты поиска

Содержание Kayak XU 03xx

Отзывы:

Похожие инструкции для Kayak XU 03xx

Бренды по названию

Популярные бренды

HP Kayak XU 03xx, Руководство по установке

Результаты поиска

Содержание Kayak XU 03xx

Отзывы:

Похожие инструкции для Kayak XU 03xx

Бренды по названию

Популярные бренды