HP Cluster Platform Скачать руководство пользователя страница 41 | Manualshive

Страница: 41 / 88

background image

•

VLAN support and tagging: support complete 802.1Q (4,096 VLAN IDs) and 256 VLANs
simultaneously

•

Traffic prioritization (802.1p): allows real-time traffic classification into 8 priority levels
mapped to 4 queues

•

Per-port broadcast throttling: selectively configure broadcast control on heavy traffic port
uplinks

•

Stacking capability: single IP address management for a virtual stack of up to 16 switches

•

HP Auto-MDIX: automatically adjusts for straight-through or crossover cables on all
10/100/1000 ports

•

Source port filters: allows only specified ports to communicate with each other

•

Troubleshooting: ingress/egress port monitoring enables network problem solving

The principal difference between the two models is in the number of ports, as shown in

Figure 2-12

. The following sections describe the HP ProCurve 2848 switch.

Figure 2-12 HP ProCurve Switch 2848 and 2824

2.6.4 ProCurve 2848 Switch Overview

The HP ProCurve 2848 is a multi-port Gigabit switch that can be connected to an external
redundant power supply (RPS) unit. The characteristics of the HP ProCurve 2848 switch include:
•

48 auto-sensing 10/100/1000Base-T RJ-45 ports

•

dual-personality ports — 10/100/1000Base-T RJ-45 ports or mini-GBIC slots for optional
fiber-optic connectivity such as Gigabit-SX, LX, or LH

•

plug-and-play networking

•

automatic learning of the network addresses

•

support for the Spanning Tree Protocol to eliminate network loops

•

96 Gbps backplane with up to 71.4 mpps

•

stacking capability: single IP address management for a virtual stack of up to 16 switches

•

port security to prevent unauthorized access using MAC address lockdown

2.6.4.1 Front View of the HP ProCurve 2848 Switch

The HP ProCurve 2848 switch has 48 auto-sensing 10/100/1000Base-T RJ-45 ports that are spread
across the front panel. To the right are four triple-speed copper gigabit ports, and below these
are four mini-GBIC slots that accept fiber-optic cables. These eight slots are referred to as
dual-personality ports because you can use either the copper port or the corresponding fiber-optic
port. Only four of the ports can be used at any one time. By default, the RJ-45 connectors are
enabled. If a mini-GBIC is installed in a slot, it is enabled and the associated RJ-45 connector is
disabled. If the mini-GBIC is removed, the associated RJ-45 port is automatically re-enabled. ???
shows the front panel of the ProCurve 2848 switch.

2.6 HP ProCurve Switches

41

«
...
39
40
41
42
43
...
»

Содержание Cluster Platform

























































































Отзывы:

Нет отзывов

Похожие инструкции для Cluster Platform

Бренд: Omneon Страницы: 2

Бренд: Vitek Страницы: 2

Бренд: Digital Equipment Страницы: 15

Бренд: IBM Страницы: 48

Бренд: TYAN Страницы: 136

Intesis IBMBSDAL0640000

Бренд: HMS Networks Страницы: 39

Бренд: Emerson Страницы: 23

DIXELL XWEB5000 PRO

Бренд: Emerson Страницы: 20

Бренд: Emerson Страницы: 18

Avocent ACS 6000

Бренд: Emerson Страницы: 93

Бренд: Emerson Страницы: 114

Centellis 2000 Shelf Release 3.0

Бренд: Emerson Страницы: 194

Бренд: Emerson Страницы: 222

Бренд: Dell Страницы: 129

PowerEdge HR675

Бренд: Dell Страницы: 194

PowerEdge FC630

Бренд: Dell Страницы: 143

PowerEdge HX574

Бренд: Dell Страницы: 202

Wyse 5020 P Series

Бренд: Dell Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды