HP Cluster Platform Скачать руководство пользователя страница 59

Страница: 59 / 88

Figure 2-35 Power Strips – Double (New HP Cluster Platform Models)

The following list describes the callouts in

Figure 2-35

Power cable

Power strip

Mounting hardware

Right rear rack column

Right rear rack chassis

Caution:

Do not use the power strips to supply power to any components not already configured into the
cluster. This could cause a power overload.

2.8.2 PDU for Scalable Visualization Array (SVA)

Scalable Visualization Arrays use a 40A PDU that mounts to the vertical rack frame. No additional
power strips are required.

Figure 2-36

shows the position of the PDU in the rear for the rack.

Note:

The PDU is mounted within U38. Viewing the back of the rack, the PDU mounts to the right rear
side of the chassis.

The PDU is provided with the following features:
•

Vertical mounting in the rear of the rack, maximizing space (no additional parts are required
for mounting)

•

Power cord retention bands

•

A front panel display that indicates operating parameters

•

A color-coded branch circuit

2.8 PDUs for Cluster Platform and Scalable Visualization Array (SVA)

Содержание Cluster Platform

























































































Результаты поиска

Содержание Cluster Platform

Отзывы:

HP Cluster Platform, Руководство по введению, Страница: 59 / 88

Результаты поиска

Содержание Cluster Platform

Отзывы: