HP Cluster Platform Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 88

background image

Meaning

State

Description

Item

Link = Indicates that the port LEDs are displaying link information. If the
port LED is on, the port is enabled and receiving a link indication from
the connected device. If the port LED is off, the port has no active network
cable connected, or is not receiving link beat or sufficient light. Otherwise,
the port may have been disabled through the switch console, the Web
browser interface, or HP TopTools. If the port LED is blinking*
simultaneously with the Fault LED, the corresponding port has failed its
self-test.

Act = Indicates that the port LEDs are displaying network activity
information.

FDx = Indicates that the port LEDs are lit for ports that are in full-duplex
mode.

Spd = Indicates that the port LEDs are displaying the connection speed at
which each port is operating. If the port LED is off, the port is operating
at 10 Mb/s. If the port LED is flashing**, the port is operating at 100 Mb/s,
and if the port LED is on continuously, the port is operating at 1000 Mb/s.

4 green LEDs

Port LED
View

6

T = Indicates the 10/100/1000Base-T RJ-45 port is enabled.

M = Indicates the mini-GBIC port is enabled.

Green — ports 49
and 50 only

T/M

7

* The blinking behavior is an on/off cycle once every 1.6 seconds, approximately.**The flashing behavior is an on/off
cycle once every 0.5 seconds, approximately.

None of the rear panels of the HP ProCurve switches have any LEDs.

5.3 HP Procurve Switch Problems

The LED patterns on the HP ProCurve switch can indicate problem conditions.

Table 5-1

describes

some of the possibilities.

Table 5-1 HP ProCurve Switch Diagnostics

Problem

Port LED

Fan Status

Self- Test

Fault

Power

The interconnect is not plugged
into an active AC power source,
or the switch's power supply may
have failed.

a

a

a

a

Off with
power cord
plugged in.

An interconnect hardware failure
has occurred. All the LEDs will
stay on indefinitely.

a

a

Prolonged on

Prolonged on

On

The interconnect has experienced
a software failure during self-test.

a

a

Blinking

b

Blinking

b

On

One or both of the cooling fans
may have failed.

a

Blinking

Off

Blinking

b

On

The network port for which the
LED is blinking has experienced
a self-test or initialization failure.

Blinking

b

a

Blinking

b

Blinking

b

On

The network connection is not
working properly.

Off with cable
connected.

a

Off

Off

On

The port may be improperly
configured, or the port may be in
a blocking state.

On, but the port
is not
communicating.

a

Off

Off

On

a

This LED is not important for the diagnosis.

b

The blinking behavior is an on/off cycle once every 1.6 seconds, approximately.

5.3 HP Procurve Switch Problems

75

«
...
73
74
75
76
77
...
»

Содержание Cluster Platform

























































































Отзывы:

Нет отзывов

Похожие инструкции для Cluster Platform

Бренд: IBM Страницы: 54

SuperServer E100-8Q

Бренд: Supermicro Страницы: 48

SuperServer 5039MD18-H8TNR

Бренд: Supermicro Страницы: 134

RS/6000 44P Series 270

Бренд: IBM Страницы: 346

Бренд: IBM Страницы: 48

DiskStation Series

Бренд: Synology Страницы: 6

callpilot 1002rp

Бренд: Avaya Страницы: 150

AcquiLite A7810-0

Бренд: Obvius, LLC Страницы: 29

PRIMERGY TX140 S2

Бренд: Fujitsu Страницы: 86

PRIMERGY TX150 S3

Бренд: Fujitsu Страницы: 95

PRIMERGY TX150 S6

Бренд: Fujitsu Страницы: 118

Бренд: Fujitsu Страницы: 305

PRIMERGY TX150 S6

Бренд: Fujitsu Страницы: 127

PRIMERGY TX140 S2

Бренд: Fujitsu Страницы: 332

PRIMERGY TX150 S4

Бренд: Fujitsu Страницы: 97

PRIMERGY TX150 S7

Бренд: Fujitsu Страницы: 120

PRIMERGY TX140 S1p

Бренд: Fujitsu Страницы: 9

Бренд: Digi Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды