HP Cluster Platform Скачать руководство пользователя страница 47

Страница: 47 / 88

Figure 2-18 TFT7600 Rear Ports

The following list corresponds to the callouts in

Figure 2-18

USB keyboard/mouse

USB pass-through (connects to a KVM switch virtual media port)

PS2 keyboard

PS2 mouse

VGA input

Power connection

Cable tray

Back of TFT7600

Serial firmware port — not shown (enables updates to TFT7600 firmware)

Note:

The TFT7600 has a USB pass-through port on the front side which is the pass-through to the rear
USB port (see callout 1 in

Figure 2-18

2.7.1.2 Brace Rail and Cable Management Arm

You do not have to remove the brace rail and cable management arm (see

Figure 2-19

) to service

the TFT7600. However, the power supply or cables might require service. This section describes
the components in the brace rail assembly that might require service. The brace rail (see callout
1 in

Figure 2-19

) mounts to the adjustable rails. The cable management arm is attached to the

back of the TFT7600 with two 6-32 screws, which must be removed to enable removal of the
TFT7600 for replacement, if necessary.

2.7 KVM and Console Switches

Содержание Cluster Platform

























































































Результаты поиска

Содержание Cluster Platform

Отзывы:

Похожие инструкции для Cluster Platform

Бренды по названию

Популярные бренды

HP Cluster Platform, Руководство по введению

Результаты поиска

Содержание Cluster Platform

Отзывы:

Похожие инструкции для Cluster Platform

Бренды по названию

Популярные бренды