HP Cluster Platform Скачать руководство пользователя страница 29 | Manualshive

Страница: 29 / 88

background image

approximately eight inches of room outside of the internal mounting rails for routing the 288-port
InfiniBand interconnect cables. The 800 mm-wide cabinet mounts flush with the standard 42U
racks, so there is no need to offset this particular model.

2.4 HP Rack 10000 G2 Series

The HP Rack 10000 G2 Series are designed for greater ease-of-use maintenance. The HP Rack
10000 G2 Series design is based on the original HP 10000 Series Racks (see

Section 2.3

) with

improvements for better airflow and cable management. The HP Rack 10000 G2 Series have
improved front and rear doors for maximum airflow, cable management, and better handles.
The HP Rack 10000 G2 Series side panels have been modified to a three-panel, tool-free design
for easier removal, handling, and access. The HP Rack 10000 G2 Series is available in 22U, 36U,
42U, 42U 800 mm-wide, and 47U cabinets.

Figure 2-5

shows an HP Rack 10000 G2 Series 42U

cabinet.

The HP Rack 10000 G2 Series 42U cabinet has the same dimensions and footprint as its
predecessor, the HP 10000 Series Rack.

Figure 2-5 HP Rack 10000 G2 Series 42U Cabinet

For more information, go to the HP 10000 G2 Series Rack website:

http://h18000.www1.hp.com/products/servers/proliantstorage/racks/10000series-g2/index.html

2.5 HP Modular Cooling System

The HP Modular Cooling System (MCS) is designed for high-density server and server blade
deployments, and is supported as an exception in HP Cluster Platform solutions. It recirculates
and cools the hot server exhaust air through heat exchangers residing in the MCS unit. The air
is then expelled in front of the enclosed rack at a much lower temperature, providing sufficient
cool air for a load of 35KW of servers or blades.

The MCS unit contains three fans and three heat exchangers deployed along the full height of
the rack to ensure that all the equipment installed receives sufficient cooled air. All fans and heat
exchangers are swappable while the unit is online, providing great servicing flexibility. Redundant
power is ensured through a failover power switch that can be connected to two power sources.
The environmental monitor controls the air temperature to the servers and adjusts automatically
to meet the pre-established air temperature goal. The environmental monitor interacts with HP
SIM (Systems Insight Manager) via SNMP traps.

The HP Modular Cooling System G2 Rack contains six fans and a heat exchanger deployed along
the full height of the rack to ensure that all of the equipment installed receives sufficient chilled
air. All fans are swappable while the unit is online, providing great servicing flexibility. Redundant
power is ensured through the failover switch that can be connected to two power sources. The

2.4 HP Rack 10000 G2 Series

29

«
...
27
28
29
30
31
...
»

Содержание Cluster Platform

























































































Отзывы:

Нет отзывов

Похожие инструкции для Cluster Platform

Бренд: F5 Страницы: 2

WANJet 400 Appliance

Бренд: F5 Страницы: 11

Бренд: Xerox Страницы: 220

Бренд: Xerox Страницы: 28

DocuPrint 100MX

Бренд: Xerox Страницы: 2

Sun Blade T6340

Бренд: Sun Oracle Страницы: 82

NovaScale T820 F2

Бренд: Bull Страницы: 34

iDataPlex dx320 6385

Бренд: IBM Страницы: 60

Бренд: d3 Technologies Страницы: 10

AND-APL1E Series

Бренд: Acrosser Technology Страницы: 42

WPS870G - Wireless Print Server

Бренд: Motorola Страницы: 115

Бренд: ICP DAS USA Страницы: 59

Бренд: ZyXEL Communications Страницы: 115

Бренд: Gigabyte Страницы: 86

Бренд: Gigabyte Страницы: 110

Бренд: Gigabyte Страницы: 173

Бренд: Gigabyte Страницы: 166

Бренд: Gigabyte Страницы: 134

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды