HP 9000 rp7410 Скачать руководство пользователя страница 94 | Manualshive

Страница: 94 / 266

HP 9000 rp7410 Скачать руководство пользователя страница 94

powered off when the OS issues a shutdown for reconfig command (for example,

shutdown -h

or

shutdown /s

).

This is the normal behavior on HP rx7620, rx7640, rx8620, and rx8640 servers with a

windows

ACPI configuration setting.

When softpowerdown is enabled on HP rx7620, rx7640, rx8620, and rx8640 servers, if
one nPartition is defined in the server, then halting the OS powers off the server cabinet
including all cells and I/O chassis. On HP rx7620, rx7640, rx8620, and rx8640 servers
with multiple nPartitions, halting the OS from an nPartition with softpowerdown
enabled causes only the resources on the local nPartition to be powered off.

To power on hardware that has been powered off, use the

PE

command at the

management processor Command menu.

—

acpiconfig disable softpowerdown

When set on HP rx7620, rx7640, rx8620, and rx8640

servers,

acpiconfig disable softpowerdown

causes nPartition cells to remain

at a boot-is-blocked state when the OS issues a shutdown for reconfig command (for
example,

shutdown -h

or

shutdown /s

). In this case an OS shutdown for reconfig

makes the nPartition inactive.

This is the normal behavior on HP rx7620, rx7640, rx8620, and rx8640 servers with an
ACPI configuration setting of

default

or

single-pci-domain

.

To make an inactive nPartition active, use the management processor

BO

command to

boot the nPartition past the boot-is-blocked state.

•

Boot Modes on HP Integrity nPartitions: nPars and vPars Modes

On cell-based HP Integrity

servers, each nPartition can be configured in either of two boot modes:
—

nPars

Boot Mode

In

nPars

boot mode, an nPartition is configured to boot any single operating system

in the standard environment. When an nPartition is in

nPars

boot mode, it cannot boot

the vPars monitor and therefore does not support HP-UX virtual partitions.

—

vPars

Boot Mode

In

vPars

boot mode, an nPartition is configured to boot into the vPars environment.

When an nPartition is in

vPars

boot mode, it can only boot the vPars monitor and

therefore it only supports HP-UX virtual partitions and it does not support booting HP
OpenVMS I64, Microsoft Windows, or other operating systems. On an nPartition in

vPars

boot mode, HP-UX can boot only within a virtual partition (from the vPars

monitor) and cannot boot as a standalone, single operating system in the nPartition.

CAUTION:

An nPartition on an HP Integrity server cannot boot HP-UX virtual partitions

when in

nPars

boot mode. Likewise, an nPartition on an HP Integrity server cannot boot

an operating system outside of a virtual partition when in

vPars

boot mode.

To check or set the boot mode for an nPartition on a cell-based HP Integrity server, use any
of the following tools as appropriate. Refer to Installing and Managing HP-UX Virtual Partitions
(vPars), Sixth Edition, for details, examples, and restrictions.

94

Booting and Resetting nPartitions

«
...
92
93
94
95
96
...
»

Содержание 9000 rp7410











































































































































































































































































Отзывы:

Нет отзывов