HP 669048-009 Скачать руководство пользователя страница 95 | Manualshive

Страница: 95 / 108

background image

Stabilizer kit 95

Stabilizer kit

About this device

The Stabilizer kit provides stability and support and prevents possible tipping when you install, remove, or
access equipment within the HP Advanced Series Racks and Enterprise Series Racks.
The stabilizer kit is either required or recommended, depending on your rack configuration. There are four

stabilizer kit options.

•

The standard 600-mm (23.6 in) or 800-mm (31.5 in) front foot is required with deployments of
stand-alone racks. Rack rows with four or more bayed racks, without a single rack-mountable

component exceeding 99.8 kg (220 lb), do not need a stabilizer kit installed.

•

The heavy duty 600-mm (23.6 in) front foot is required when a single rack-mountable component

weighing 99.8 kg (220 lb) or more is installed in a stand-alone rack or in a rack belonging to a rack

row of three or fewer bayed racks.

Kit contents

Item

Quantity

600-mm (23.62-inch) Front stabilizer mount

1

Stabilizer feet

2

M8 x 30-mm bolt

8

M8 flat washer

8

This kit might contain extra hardware for your convenience.

Required tools

The following tools are required for installation:

•

Ratchet with sockets

•

Adjustable wrench

Installing the stabilizer

NOTE:

HP recommends using the side feet, provided with this kit, to stabilize stand-alone racks

from the side. If you are stabilizing racks that are secured together with baying kits, the side feet

are optional on either end of the row.

1.

Raise the rack with leveling feet to align the front foot with the front caster plate.

«
...
93
94
95
96
97
...
»

Содержание 669048-009













































































































Отзывы:

Нет отзывов

Похожие инструкции для 669048-009

Бренд: M-system Страницы: 5

Бренд: Samsung Страницы: 2

Бренд: Radial Engineering Страницы: 4

Бренд: Basalte Страницы: 2

Бренд: Wheelock Страницы: 1

Бренд: GameKeeper Страницы: 13

Бренд: K&M Страницы: 2

Бренд: HAGOR Страницы: 12

Бренд: QualGear Страницы: 2

Бренд: ricoo Страницы: 28

Бренд: Konig & Meyer Страницы: 6

Бренд: Atdec Страницы: 6

Бренд: Atlas Страницы: 2

Бренд: Shop fox Страницы: 12

Бренд: Jackson Страницы: 9

Бренд: Jackco Страницы: 6

Бренд: XROCKER Страницы: 4

Бренд: XPOtool Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды