HP 669048-009 Скачать руководство пользователя страница 24

Страница: 24 / 108

Airflow Optimization kit 24

Airflow Optimization kit

About this device

The Airflow Optimization kit enables you to install foam rail gaskets in your HP Advanced Series Racks and
Enterprise Series Racks 36U, 42U, and 47U 600-mm (24-in) wide racks and in to 42U 800-mm (31-in) wide

racks to improve separation between hot and cold aisles in the data center.

Kit contents

Item

Quantity

Foam rail gasket roll

600-mm (24-in) perforated floor
gasket

—or—
800-mm (31-in) perforated floor

gasket

Extra hardware might be included for your convenience.

Required tools

No tools are required for this procedure.

Installing foam rail gaskets between racks

CAUTION:

The foam rail gasket must be installed into the rack before two or more racks can be

bayed together. For additional information on baying racks, see the

HP Baying Rack Option Kit

If installing the foam rail gasket between racks that have a baying kit installed, the baying bracket must be

removed before the foam rail gasket can be inserted between the racks.

Position the racks side by side.

Cut the foam rail gasket to fit the size of your rack.

Содержание 669048-009













































































































Результаты поиска

Содержание 669048-009

Отзывы:

Похожие инструкции для 669048-009

Бренды по названию

Популярные бренды

HP 669048-009, Руководство по установке

Результаты поиска

Содержание 669048-009

Отзывы:

Похожие инструкции для 669048-009

Бренды по названию

Популярные бренды