HP 445860-B21 - 10Gb Ethernet BL-c Switch Скачать руководство пользователя страница 72

Страница: 72 / 262

Dashboard

Table 45

RIP Interfaces Dashboard controls

Control Description

Poisoned Reverse

Displays whether Poisoned Reverse is enabled or disabled.

Triggered Updates Displays whether Triggered Updates is enabled or disabled.

Multicast Updates

Displays whether Multicast Updates is enabled or disabled.

Metric

Displays the route metric for the interface.

Auth Type

Displays the authentication type for the interface.

Auth Key

Displays the authentication key for the interface.

Split Horizon

Displays whether Split Horizon is enabled or disabled.

Содержание 445860-B21 - 10Gb Ethernet BL-c Switch







































































































































































































































































Результаты поиска

Содержание 445860-B21 - 10Gb Ethernet BL-c Switch

Отзывы:

Похожие инструкции для 445860-B21 - 10Gb Ethernet BL-c Switch

Бренды по названию

Популярные бренды

HP 445860-B21 - 10Gb Ethernet BL-c Switch, Справочное руководство

Результаты поиска

Содержание 445860-B21 - 10Gb Ethernet BL-c Switch

Отзывы:

Похожие инструкции для 445860-B21 - 10Gb Ethernet BL-c Switch

Бренды по названию

Популярные бренды