HP 445860-B21 - 10Gb Ethernet BL-c Switch Скачать руководство пользователя | Manualshive

Страница: 214 / 262

background image

Configuring the switch

214

Default Gateway Configuration

To display the following form, go to the Default Gateways Configuration form. Select a Default Gateway
ID, or open the Default Gateways folder and click

Add Default Gateway.

Default Gateways are disabled by default.
The following table describes the Default Gateway Configuration controls:

Table 146

Default Gateway Configuration controls

Control Description

Default Gateway Identifier (1-4, 254)

Selects a default Gateway to configure.

Default Gateway IP Address

Configures the IP address of the default IP gateway using dotted decimal
notation.

Enable/Disable Default Gateway

Enables or disables the gateway for use.

Enable/Disable ARP only health checks

Enables or disables Address Resolution Protocol (ARP) health checks. This
command is disabled by default.

Health Check Interval (0-60 sec)

The switch pings the default gateway to verify that it’s up. The interval

option sets the time between health checks. The range is from 0 to 60
seconds. The default is 2 seconds.

Retries before Out of Service (1-120)

Sets the number of failed health check attempts required before declaring

this default gateway inoperative. The range is from 1 to 120 attempts.
The default is 8 attempts.

«
...
212
213
214
215
216
...
»

Содержание 445860-B21 - 10Gb Ethernet BL-c Switch







































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 445860-B21 - 10Gb Ethernet BL-c Switch

Бренд: 3idee Страницы: 7

Бренд: U.S. Converters Страницы: 12

Бренд: Parker Страницы: 36

Бренд: NI Страницы: 11

HandyPort HPU-120

Бренд: HandyWave Страницы: 19

Бренд: Rocom Страницы: 2

Linksys SPA9000

Бренд: Linksys Страницы: 246

Бренд: Dell Страницы: 49

EtherExpress Pro/10+

Бренд: Dell Страницы: 16

Бренд: Dell Страницы: 17

Бренд: Dell Страницы: 11

Бренд: Dell Страницы: 101

Бренд: Dell Страницы: 10

Latitude E6400 XFR

Бренд: Dell Страницы: 74

TrueMobile 1300

Бренд: Dell Страницы: 142

Latitude E6400 XFR

Бренд: Dell Страницы: 81

PowerVault MD3000

Бренд: Dell Страницы: 102

Бренд: Dell Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды