HP 445860-B21 - 10Gb Ethernet BL-c Switch Скачать руководство пользователя

Страница: 69 / 262

Dashboard

OSPF Virtual Links Dashboard

To display the following form, select

Layer 3 > OSPF > Virtual Links

(click the underlined text, not

the folder).

The following table describes the OSPF Virtual Links Dashboard controls:

Table 43

OSPF Virtual Links Dashboard controls

Control Description

Virtual Link

Displays the virtual link number.

Enabled?

Displays the status of the virtual link, either enabled or disabled.

Area Number

Displays the area number associated with the virtual link.

Neighbor Router ID

Displays the neighbor router ID.

Transit Delay

Displays the transit delay value, in seconds.

Содержание 445860-B21 - 10Gb Ethernet BL-c Switch







































































































































































































































































Результаты поиска

Содержание 445860-B21 - 10Gb Ethernet BL-c Switch

Отзывы:

Похожие инструкции для 445860-B21 - 10Gb Ethernet BL-c Switch

Бренды по названию

Популярные бренды

HP 445860-B21 - 10Gb Ethernet BL-c Switch, Справочное руководство

Результаты поиска

Содержание 445860-B21 - 10Gb Ethernet BL-c Switch

Отзывы:

Похожие инструкции для 445860-B21 - 10Gb Ethernet BL-c Switch

Бренды по названию

Популярные бренды