HP 16500A Скачать руководство пользователя страница 81

Страница: 81 / 144

The Color Display Test

The Color Display Test is used to test the display.

This test is not normally needed. These screens are primarily used when the color module requires
adjusting. For the adjustment procedure, refer to section 4-5, "Color Display Module Adjustments."

To check for color purity, proceed as follows:

1. From the Mainframe Test menu, touch the Color Display Test. The white cross-hatch pattern is

displayed. This pattern is used for the color module geometry adjustments.

2. Touch the Continue field. The white raster pattern is displayed. With every touch of the Continue

field, the next color test pattern is displayed. See figure 6-9.

3. Touch Continue from the black raster pattern to display the Mainframe Test menu. Note that the

Display Test status has changed from UNTESTED to TESTED.

Figure 6-9. Selecting the Color Display Patterns

HP 16500A/16501A - Service

6-12

Содержание 16500A

















































































































































Результаты поиска

Содержание 16500A

Отзывы:

HP 16500A, Руководство по обслуживанию, Страница: 81 / 144

Результаты поиска

Содержание 16500A

Отзывы: