HP 16500A Скачать руководство пользователя страница 11

Страница: 11 / 144

1-6. Accessories Available

The accessories available for the
HP 16500A/16501A include the following:

•

HP 46060A Mouse.

•

HP E2427A Keyboard.

•

HP-IB Cables: HP 10833A, 10833B,
10833C, 10833D.

•

Hewlett-Packard Printers (see table 1-1).

•

Extra Operating and Programming Manual
(Option 910).

•

HP 1008A Testmobile.
Option 006 Power Strip and Cabinet.

•

Extended Repair Service (Option W30).

•

RS-232C DTE to DTE Cable. Used for
connecting the HP 16500A to printers and
controllers. HP Part Number 13242-60010.

•

RS-232C DTE to DCE Cable. Used for
connecting the HP 16500A to modems and
data switch. HP Part Number 13242-60001.

•

HP 74240A/74240B CAE Software.

•

Rackmount Kit HP Part Number 5061-9679.

•

Transit Case HP Part Number 9211-2658.

•

Hewlett-Packard Plug-In Modules with data
acquisition, stimulus, pattern generator, and
oscilloscope capabilities.

•

Blank 3.5-inch disks (box of 10) HP Part
Number 92192A.

For more information about plug-in modules or
accessories, contact the nearest Hewlett-Packard
Sales Office.

1-7. Operating Characteristics

Table 1-1 is a listing of the instrument’s operating
characteristics. These are not specifications, but
are typical operating characteristics included as
additional information for you.

1-8. Recommended Test Equipment

The equipment required to test and maintain the
HP 16500A/16501A is listed in table 1-2.

Other equipment may be substituted if it meets or
exceeds the critical specifications listed in the
table.

HP 16500A/16501A - General Information

1-3

Содержание 16500A

















































































































































Результаты поиска

Содержание 16500A

Отзывы:

HP 16500A, Руководство по обслуживанию, Страница: 11 / 144

Результаты поиска

Содержание 16500A

Отзывы: