HP 16500A Скачать руководство пользователя страница 44

Страница: 44 / 144

Geometry Adjustments

1. From the Mainframe Test System, select the Display Test menu. Select the white cross hatch test

pattern. Refer to section 4-4, "Adjustment Test Patterns," for accessing the test patterns.

2. Preset the front panel BACKGROUND control to mechanical center.

3. Preset the front panel BRIGHTNESS control to maximum.

4. Preset H.SUB SHIFT (RV006) and V.SUB SHIFT (RV008), located on the bottom PC board, to

mechanical center.

5. Using a flexible ruler, adjust H.SIZE (RV504) and V.HEIGHT (RV502), located on the left hand side

PC board, so that the border of the cross-hatch is 120.5 mm (4.74 in.) vertically and 161 mm
(6.34 in.) horizontally.

6. Adjust V.CENT (RV510) and H.CENT (RV503), located on the left hand side PC board, to center

pattern.

7. Adjust PIN AMP (RV506), located on the left hand side PC board, to eliminate pincushion distortion

in the vertical lines of the cross-hatch pattern as shown in figure 4-12.

Figure 4-12. PIN AMP Adjustment

HP 16500A/16501A - Adjustments

4-9

Содержание 16500A

















































































































































Результаты поиска

Содержание 16500A

Отзывы:

HP 16500A, Руководство по обслуживанию, Страница: 44 / 144

Результаты поиска

Содержание 16500A

Отзывы: