HP 16500A Скачать руководство пользователя страница 135

Страница: 135 / 144

Transferring Parts to the Replacement Module

The purpose of this procedure is to transfer the mechanical parts from the old module to the replacement
module.

1. Remove the rear mounting bracket from the rear support bracket. Remove the rear support bracket

from the color display module.

2. Attach the rear support bracket to the replacement module, using the two thread-forming screws.

Do not overtighten.

3. Attach the frame mounting bracket to the rear support bracket. Install hardware in the following

sequence: screw, flat washer, rubber washer. Do not tighten the hardware.

4. Remove the four bracket nuts connecting the front mounting brackets to the old module, then

remove the front mounting brackets. Reinstall the bracket nuts on the old module.

5. Remove the four bracket nuts from the replacement module. Using the four bracket nuts, install

both front mounting brackets on the replacement display module. The upper bracket is identified
by the notch on one edge.

6. Disconnect the flat microprocessor cable, the power cable, and the front-panel control cable from

the old module, noting the location of the cables. Connect the cables to the replacement module.

HP 16500A/16501A - Service

6-66

Содержание 16500A

















































































































































Результаты поиска

Содержание 16500A

Отзывы:

HP 16500A, Руководство по обслуживанию, Страница: 135 / 144

Результаты поиска

Содержание 16500A

Отзывы: