HP 16500A Скачать руководство пользователя страница 137

Страница: 137 / 144

Installing the Replacement Color Display Module

1. Carefully slide the color display module most of the way into the mainframe. To prevent damage to

the cables, make sure that they clear the mainframe.

2. Connect the color display to power supply cable to the power supply. Slide the display module

completely into the mainframe.

3. Attach the display module to the front frame with four screws (two on the top casting and two on the

bottom casting). Do not tighten the screws.

4. Move the sheet metal nuts, located on the front tabs of the center board guide, so that the holes in

the sheet metal nuts and the tabs line up. Attach the front tabs of the center board guide to the
front frame.

5. Reinstall the front-panel assembly, connecting the front-panel cables. Make sure the front-panel

assembly is properly seated before tightening the hardware.

6. Push the display module forward, until it is properly seated against the front-panel assembly.

Tighten the four display module mounting screws in the front frame.

7. Attach the rear mounting bracket of the display module to the side frame, then tighten the mounting

bracket screws. To prevent damage to the rubber washers, do not overtighten the screws.

8. Tighten all of the display module mounting hardware. Reconnect the flat color display to

microprocessor cable to the microprocessor board.

9. Reinstall all covers.

HP 16500A/16501A - Service

6-68

Содержание 16500A

















































































































































Результаты поиска

Содержание 16500A

Отзывы:

HP 16500A, Руководство по обслуживанию, Страница: 137 / 144

Результаты поиска

Содержание 16500A

Отзывы: