HP 16500A Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 144

HP 16500A Скачать руководство пользователя страница 112

8. Select Run on the HP 1651B, then scroll the data to fill the screen. The results on the HP 1651B

screen should show the Data and Address alternating between AA and 55. See figure 6-37.

Also, the screen should show the Strobe with a hexadecimal representation of walking 0s through
the data bits. See figure 6-37. The hexadecimal (hex) representation can be changed to a binary
representation as shown below.

Hex

Binary

1E

11110

1D

11101

1B

11011

17

10111

0F

01111

If the test results are not correct, replace the mainframe interface card and reconfigure the
HP 16500A/16501A system. Then, return to the Expansion Frame Flowchart 12.

If the test results are correct, reconfigure the HP 16500A/16501A system. Then, continue with
this procedure.

Interface Cable

9. Turn off the HP 16500A/16501A system, then remove the power cord from the mainframe and from

the expansion frame. Remove all option modules from the expansion frame.

10. Remove the expansion interface card far enough to read the reference designators of the

components on the back of the card (closest to the rear panel). To remove the expansion interface
card (board), refer to section 6-20, "Expansion Interface Board Replacement."

6-37. HP 1651B Test Screen

HP 16500A/16501A - Service

6-43

«
...
110
111
112
113
114
...
»

Содержание 16500A

















































































































































Отзывы:

Нет отзывов