Howard M9 страница 8 Скачать руководство пользователя

Страница: 8 / 62

Technical Service Manual M9 Transfer Stretcher (M999-29, Version 11, June 2021)

2. PRECAUTIONS

WARNING: Only connect the stretcher to a mains supply with protective earth.

WARNING: Before using a mobile patient hoist, check underbed clearance.

WARNING: Do not use in an oxygen rich environment or any flammable gas environment.

WARNING: Do not modify any component or accessory without prior authorisation from Howard Wright Limited.

WARNING: Do not transport patients where the stretcher may become unstable

For example, inclines over 10 degrees.

WARNING: When routing cables from other equipment onto the stretcher, take precaution to avoid

the cables being squeezed between stretcher components.

WARNING: Always handle the power cord with care and keep it clear of any moving parts.

WARNING: Ensure the power cord and plug are always accessible.

WARNING: The supply plug is the only disconnection device.

CAUTION: Always stow the power cord and other equipment before transporting the stretcher.

CAUTION: The leg-raise panel must be physically supported when cleaning the underside.

Содержание M9































































Результаты поиска

Содержание M9

Отзывы:

Похожие инструкции для M9

Бренды по названию

Популярные бренды

Howard M9, Техническое и сервисное руководство

Результаты поиска

Содержание M9

Отзывы:

Похожие инструкции для M9

Бренды по названию

Популярные бренды