Howard M9 страница 21 Скачать руководство пользователя

Страница: 21 / 62

Technical Service Manual M9 Transfer Stretcher (M999-29, Version 11, June 2021)

7. SERVICE INSTRUCTIONS

CONTROL BOX - CB16

ummary:

This service instruction outlines the procedure to replace the CB16 control box.

Tools Required:

• 5mm hex key

• 7mm spanner

• 8mm spanner

• small flat blade screwdriver

Parts Required:

• 1x CB16 control box

• 1x std cable tie.

Location:

The control box is attached to the cord holder plate at the head end (HE) of the deck.

WARNING:

Ensure all cables are secured away from moving parts.

WARNING:

Ensure a portable appliance test is conducted after the

CB16 Control Box is replaced.

Procedure:

1. Raise the deck to the maximum height position and apply castor

brakes.

2. Unplug the stretcher from the mains supply.

3. Cut the cable tie securing cables to the centre of the cover plate.

4. With a 7mm spanner, disconnect the earth cables from the earth

stud on the control box. Keep washer for reassembly.

5. Remove the power cord plug from the control box by pushing in the

retaining clips with a small flat blade screwdriver and pulling power

cord. The retaining clips are two red pins on either side of the plug

port.

6. Remove the control box cable clip and unplug all the cables, keeping

the plugs in order (mark if necessary).

7. Using an 8mm spanner, remove the four M5 nyloc nuts securing the

control box to the mounting plate.

8. Carefully remove the control box.

9. Reverse the procedure to install the new control box (see warning

above).

NOTE:

If needed, refer to the electric circuit section for more detail

on specific ports and their respective plugs.

10. Conduct a PAT test on the stretcher.

11. Plug the power cord into the mains supply and initialise the control

box (See 6.5 on page 12). Verify all stretcher functions are working

correctly before returning to service.

Содержание M9































































Результаты поиска

Содержание M9

Отзывы:

Похожие инструкции для M9

Бренды по названию

Популярные бренды

Howard M9, Техническое и сервисное руководство

Результаты поиска

Содержание M9

Отзывы:

Похожие инструкции для M9

Бренды по названию

Популярные бренды