Howard M9 страница 23 Скачать руководство пользователя

Страница: 23 / 62

Technical Service Manual M9 Transfer Stretcher (M999-29, Version 11, June 2021)

BACKREST ACTUATOR

ummary:

This service instruction outlines the procedure to replace the backrest actuator.

Tools Required:

• 4mm hex key

• 5mm hex key

• 2x 13mm spanners

• side cutters

• small flat blade screwdriver

Parts Required:

• 1x backrest actuator

Location:

The backrest actuator (A) is located on the left side of the stretcher.

WARNING:

Ensure the actuator cable is secured away from

moving parts, but allowing sufficient length for

actuator movement.

WARNING:

Ensure the CPR Quick Release function is

operating correctly.

Procedure:

1. Raise the deck to the maximum height position, ensure the

deck is flat and apply castor brakes.

2. Unplug the stretcher from the mains supply.

NOTE:

Raise siderail for access.

3. Using a 4mm hex key, remove the two m6x8 button head

capscrews attaching the cover panel to the deck.

NOTE:

For pre June 2015 Models, remove plug locator

securing the cable plug to the actuator.

4. Using a small flat blade screwdriver, remove the cable

locking ring by pushing in the retainer clips either side of

the plug port. Unplug the actuator cable.

5. Using a 5mm hex key and a 13mm spanner, disconnect

the rear of the actuator by removing the shoulder bolt.

7. SERVICE INSTRUCTIONS

Figure 5.

Location of backrest actuator.

(Note that deck should be flat during actuator replacement)

Figure 6.

Quick release cover.

Содержание M9































































Результаты поиска

Содержание M9

Отзывы:

Похожие инструкции для M9

Бренды по названию

Популярные бренды

Howard M9, Техническое и сервисное руководство

Результаты поиска

Содержание M9

Отзывы:

Похожие инструкции для M9

Бренды по названию

Популярные бренды