Howard M9 Скачать руководство пользователя страница 25

Страница: 25 / 62

Technical Service Manual M9 Transfer Stretcher (M999-29, Version 11, June 2021)

KNEEBREAK ACTUATOR

ummary:

This service instruction outlines the procedure to replace the kneebreak actuator.

Tools Required:

• 5mm hex key

• 13mm spanner

• side cutters

Parts Required:

• 1x kneebreak actuator

Location:

The kneebreak actuator (A) is located on the left side of the stretcher.

WARNING:

Ensure the actuator cable is secured away from

moving parts, but allowing sufficient length for

elevator movement.

Procedure:

1. Raise the deck to the maximum height position, ensure the

deck is flat and apply castor brakes.

2. Unplug the stretcher from the mains supply.

NOTE:

For pre June 2015 Models, remove plug locator

securing the cable plug to the actuator.

3. Using a 5mm hex key and a 13mm spanner, disconnect

the actuator by removing the two shoulder bolts holding

the actuator at either end.

NOTE:

Raise siderail for access to actuator.

4. Reverse the procedure to install the new kneebreak

actuator (see warning above).

5. Plug the power cord into the mains supply. Verify all

stretcher functions are working correctly before returning

to service.

7. SERVICE INSTRUCTIONS

Figure 7.

Location of kneebreak actuator.

(Note that deck should be flat during

actuator replacement)

Содержание M9































































Результаты поиска

Содержание M9

Отзывы:

Бренды по названию

Популярные бренды

Howard M9, Техническое и сервисное руководство

Результаты поиска

Содержание M9

Отзывы:

Бренды по названию

Популярные бренды