Howard M9 страница 11 Скачать руководство пользователя

Страница: 11 / 62

Technical Service Manual M9 Transfer Stretcher (M999-29, Version 11, June 2021)

4. CATALOGUE INFORMATION

HEADING REFERENCES

Item Number (ITEM NO.)

• Directs you to the part in the illustration.

Part Number (PART NO.)

• Howard Wright Limited’s part number for part.

• If part number is not listed, part is not supplied.

Quantity (QTY.)

• Describes how many times a part is used in the group of parts illustrated.

PRICING

• For a current price list please contact our sales department stating which currency you require.

• Unit prices will not include GST (Goods and Service Tax) or the cost of freight.

• A minimum charge may apply for small orders.

• Howard Wright Limited reserves the right to alter prices without notice.

ORDERING

When ordering please give the following information:

1. Part number and part description.

2. Model (MODEL:), Date of manufacture (DATE:) and serial number (SN:).

This information is recorded on the serial number label located at the left side of the foot-end of deck frame.

MEASUREMENTS

All measurements are in millimetres (mm) unless otherwise stated.

ILLUSTRATIONS

• Not all illustrations are drawn to scale.

• A broken line indicates where a part is positioned or aligned.

• Where practical, views of illustrations are based on the following:

ORIENTATION TERMINOLOGY

NOTE: The terms head-end (HE), foot-end (FE), left side and right side are referenced with respect to a

patient lying face up on their back.

Left side

Head

end Foot

end

Right side

Содержание M9































































Результаты поиска

Содержание M9

Отзывы:

Похожие инструкции для M9

Бренды по названию

Популярные бренды

Howard M9, Техническое и сервисное руководство

Результаты поиска

Содержание M9

Отзывы:

Похожие инструкции для M9

Бренды по названию

Популярные бренды