Hoval UltraOil 65 Скачать руководство пользователя страница 27

Страница: 27 / 44

In the case of star-shaped data bus networks, double

earthing is not permitted. The earthing must be carried

out on one side at the star point.

Earthing for star-shaped data bus

Abschirmung

4-Draht-Bus

Shielding

4-wire bus

•

The outdoor sensor must not be mounted in the vicin-

ity of transmitters and receivers (on garage walls near

receivers for garage door openers, amateur radio an-

tennae, radio alarm installations or in the immediate

vicinity of large transmitters, etc.).

Maximum permitted cable lengths for cables carrying

sensor and low voltage (without PWM):

Min. 0.5 mm

Max. permitted cable length: 50 m

Max. PWM cable length according to pump specifi cation

Longer connecting cables should be avoided because of

the danger of radiated interference!

Interbuilding installations

•

Inter-building installations and laying the bus line under-

ground are not permitted

•

Where possible, avoid routing low-voltage and safety

extra-low voltage cables (CAN bus line) in parallel in

adjacent buildings (overbuildings) or through under-

ground car parks. If this cannot be avoided, one or

more of the following options should be selected to im-

prove the decoupling:

Increase the spacing distance

Route cables in a metal cable tray or metal cable duct

that is enclosed on all sides, and must be well earthed

Use high-quality twisted-pair cables

•

Potential diff erences between CAN_H, CAN_L and

ground must be kept low

•

If there are higher potential diff erences, the frequency

of errors will increase until the point when bus traffi c is

completely blocked

To ensure correct electrical installation, unit connec

tion and equipotential bonding (energy supply com

pany and building installation), all applicable laws,

regulations and standards must be complied with;

in particular, the regulations of the responsible ener

gy supply company. Common equipotential bonding

must be carried out in accordance with the regula

tions and standards. The cable shield is not allowed

to be used for equipotential bonding.

The work is only allowed to be carried out by quali

fi ed specialist personnel. It is the responsibility of the

electrician to ensure appropriate EMC installation.

4 213 787 / 01

InSTALLATIOn

Содержание UltraOil 65













































Результаты поиска

Содержание UltraOil 65

Отзывы:

Похожие инструкции для UltraOil 65

Бренды по названию

Популярные бренды

Hoval UltraOil 65, Техническая информация Инструкции по установке

Результаты поиска

Содержание UltraOil 65

Отзывы:

Похожие инструкции для UltraOil 65

Бренды по названию

Популярные бренды