Hoval UltraOil 65 Скачать руководство пользователя страница 30

Страница: 30 / 44

NOTICE

The minimum inner diameter of the conden

sate drain must be 15 mm. The condensate

drain must be sufficiently inclined.

it is not required to neutralise condensate from

a condenser oil-fired boiler of up to 120 kW

drained together with domestic waste water

from a private household.

CH:

For the UltraOil

, the fuel used must be heat

ing oil EL low-sulphur. As a rule, neutralisation

of the condensate is not necessary. Regard

ing the discharge of condensate, local regula

tions must be taken into account.

For the UltraOil

, the fuel used must be heat

ing oil EL low-sulphur. Neutralisation is there

fore unnecessary. Regarding the discharge of

condensate, the local regulations and the ATV

(Sewage Engineering Association) data sheet

must be observed.

NOTICE

The siphon must be filled with water before

com missioning.

4.7

Setting the temperature controller

Basic setting of the controls will be undertaken by the

heating installation engineer. Choice and setting of the

various heating programmes in accordance with the op

erating instructions.

4.8

Safety valves

The heating equipment and hot water system must be

protected with one safety valve each against unauthor

ised high pressures. Their blowing off performance must

correspond with the boiler’s maximum nominal heating

output. The valve is to be installed in the feed line in the

immediate vicinity of the boiler.

4.9

Loading pump (boiler with water heater)

Rotation speed and performance must correspond with

the requirements of the water heater. Setting carried out

by the heating installation engineer.

4.10 Heating pump

Rotation speed and performance must correspond with

the requirements of the plant. They are to be set by the

heat ing installation engineer.

4.5

Hydraulic integration

Examples

Direct heating circuit

Fig. 32

Mixer circuit and water heater

Fig. 33

4.6

Condensate discharge

The condensate discharge must be manufactured of cor

rosion-resistant material.

The following materials are suitable for the condensate

discharge:

PVC, PE, PP, RED

4 213 787 / 01

InSTALLATIOn

Содержание UltraOil 65













































Результаты поиска

Содержание UltraOil 65

Отзывы:

Похожие инструкции для UltraOil 65

Бренды по названию

Популярные бренды

Hoval UltraOil 65, Техническая информация Инструкции по установке

Результаты поиска

Содержание UltraOil 65

Отзывы:

Похожие инструкции для UltraOil 65

Бренды по названию

Популярные бренды