manualshive.com logo in svg

horsch SW 600, Руководство пользователя

Поделиться
Скачать
horsch SW 600 Скачать руководство пользователя страница 75

 

 

   

 

 

SW600 Owner’s Manual – Version 1.2 07/2018                          

  75

 

  www.horsch.com 

Track System Installation 

NOTE:  Installation procedure for machines switching from tires to track system. 

1.  Clean the implement thoroughly before proceeding with the installation. Removal of dirt and 

debris makes access to the frame and attaching fasteners easier. 

2.  Move the implement to a hard, level surface to ensure a stable work area to support the 

implement during the track system installation. 
 

 

 

IMPORTANT: Locate the identification tags, as shown above, on both undercarriages, and 
record the model number and serial numbers on warranty certificate for your records. 

3.  Raise and support implement such that the rear tires, or axle are just off the ground. 

 

 

4.  Remove the tire and rim assemblies, if applicable. 
5.  Remove the axle and hub assemblies from the implement frame (as required). 
6.  Install track fitment axle. For two axle mid-roller track systems, make sure the stabilizer 

brackets on the axle are facing to the front of the implement. Tighten mounting hardware. 
 

 

   Serial # Plate   

IMPORTANT 

Safety of the installation depends on the right operation in lifting and supporting the 
machine. Check the work area thoroughly and work in a level area. Respect safe 
operating practices, operate in conditions of enough light. Make sure the free spaces 
of the work area are suitable for the dimensions of the parts to be handled and for the 
lifting equipment maneuvers. Be careful: risk of injury. 

IMPORTANT 

Should a motorized lifting device be used, assistance on ground during operation of 
handling, coupling and assembly is needed. 

Do not stand between lifting device and axle assembly when mounting axles to 
implement. Be careful: risk of injury. 

Содержание SW 600





































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды