horsch SW 600 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 100

background image

30

SW600 Owner’s Manual – Version 1.2 07/2018

www.horsch.com

Transport Safely

Always travel at a reasonable and safe speed. Never exceed 16 mph.

Never transport with any tank more than half full. If tanks are full travel speed should not exceed 10 mph.

Never transport with fan running.

Shift the tractor in to a lower range or gear when transporting down steep slopes or hills. Latch the tractor
left and right brakes together so when in use the tractor brakes evenly. Stop slowly.

Avoid loss of control due to decreased braking ability when transporting down sloped roadways, wet or
muddy roadways or roadways covered with loose gravel or sand.

Avoid steep slopes. Some slopes may exceed tractor braking capability.

Transport only with a properly sized tractor.

Refer to ‘Calculating Minimum Tractor Weight for Safe Transport’ before transporting down a hill. Shift
tractor to a lower gear and travel at a reduced speed. Reducing the speed maximizes stability and control
and the tractors braking capability.

Use engine braking to reduce speed if available.

Avoid sharp turns or rapid steering corrections on slopes.

Stopping distance increases with speed and weight of towed loads, and on slopes. Towed loads with or
without brakes that are too heavy for the tractor or are towed too fast can cause loss of control. Consider
the total weight of the equipment and its load.

Observe these recommended maximum road speeds, or local speed limits which may be lower:

•

Do not tow this implement faster than 20 Mph (32 Km/h)

•

Never transport seed wagon when loaded on roadways

•

Never tow this implement over 10 mph when fully loaded

Ensure the load does not exceed the recommended weight ratio. Add ballast to recommended maximum
for tractor, lighten the load, or get a heavier towing unit. The tractor must be heavy and powerful enough
with adequate braking power for the towed load. Use additional caution when towing loads under adverse

surface conditions, when turning, and on inclines.

«
...
28
29
30
31
32
...
»

Содержание SW 600





































































































Отзывы:

Нет отзывов

Похожие инструкции для SW 600

ACS880-01 Series

Бренд: ABB Страницы: 238

Бренд: Cadman Страницы: 66

Бренд: Federal Страницы: 43

Бренд: dbx Страницы: 12

Бренд: dbx Страницы: 13

Бренд: dbx Страницы: 72

Бренд: dbx Страницы: 11

Бренд: dbx Страницы: 16

Бренд: Gardigo Страницы: 24

Бренд: Gardner Bender Страницы: 8

Бренд: Garantia Страницы: 4

Бренд: NARIKA Страницы: 2

Бренд: IDEAL Networks Страницы: 10

Бренд: R&S Страницы: 371

Бренд: R.M. Young Страницы: 9

Бренд: Xaoc Devices Страницы: 8

Бренд: Garmin Страницы: 2

Бренд: Parker Страницы: 58

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды