horsch SW 600 Скачать руководство пользователя страница 42 | Manualshive

Страница: 42 / 100

background image

42

SW600 Owner’s Manual – Version 1.2 07/2018

www.horsch.com

Transport & Installation

There is higher danger of accident during initial installation. Please pay attention to the notes in the
corresponding chapters.

Delivery

The machine with implements is normally delivered completely assembled on a low loader.
If parts or modules had to be disassembled for transportation purposes, these will be assembled and
installed on site by an authorized dealer or distributor.
Depending on the design of the low loader the machine can be unloaded with a tractor, or needs to lift
off with suitable lifting gear (forklift truck or crane).
Sufficient load bearing capacity of lifting gear and lifting tackle must therefore be assured.
Lifting and latching points are identified by labels.
When using other lifting points pay careful attention to the center of gravity and the weight distribution.
These points must, in any case, only be on the frame of the machine.

Installation

Instruction of the operator and initial installation of the machine will be carried out by our service
technicians or authorized dealers.

Any use of the machine without dealer/distributor training is prohibited!

The machine can only be released for operation after the instructional session has been conducted by
our service technician or authorized dealer and after the operating instructions have been reviewed and
understood.

There is higher danger of accident during installation and maintenance. Before
performing any installation and maintenance work or service, make yourself
familiar with the machine and read the operating instructions.

Depending on scope of equipment:

• Remove all parts from the hopper.

•

Take loosely delivered parts off the machine.

• Check all important screw connections!
• Lubricate all grease fittings!
• Check air pressure in tires!
• Check all hydraulic connections and hoses for correct fastening and function.
• Immediately rectify any occurring damage or have it corrected by an authorized dealer!

«
...
40
41
42
43
44
...
»

Содержание SW 600





































































































Отзывы:

Нет отзывов

Похожие инструкции для SW 600

Бренд: Landoll Страницы: 6

Бренд: ParaBody Страницы: 9

Бренд: ParaBody Страницы: 3

Бренд: MacDon Страницы: 45

Бренд: H&S Страницы: 30

Giraffe OmniBed

Бренд: Ohmeda Страницы: 54

4 Happy Kids GUCIO

Бренд: 4iQ Страницы: 12

Бренд: 4iiii Страницы: 36

Бренд: 4iiii Страницы: 34

Бренд: 4EVAC Страницы: 27

Бренд: Bartscher Страницы: 28

Бренд: Bartscher Страницы: 13

Бренд: IBEX Страницы: 10

Бренд: M-system Страницы: 12

Бренд: jablotron Страницы: 2

Бренд: M-Audio Страницы: 12

Бренд: M-Audio Страницы: 64

Бренд: M-Audio Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды