Horizon Reverse Osmosis Seafari Versatile SFC-1400-2 Скачать руководство пользователя страница 85

HRO

Systems

 Horizon 

Seafari

 “Section I” System Troubleshooting Guide

 

4.

 

If the voltage measured in the step 3 matches the system voltage, then problems may be in the 
motor wiring or the motor itself. 

 
5.

 

If low or no voltage present in the step 3 above, then check for proper operation of the Booster 
Pump Contactor.  To deactivate the contactor, press the “Stop” switch twice.  To activate the 
contactor again press “Booster Pump” switch. 

 
6.

 

If the contactor is mechanically operating, but no voltage present at the motor terminal (step 3 
above), then the contactor may be at fault. 

 
7.

 

If the contactor does not operate mechanically, then measure DC voltage between A1 and A2 
terminals.  It should read 12V DC when activated. 

 
8.

 

If the contactor gets 12V DC, but inoperative, then its coil may be open.  Replace the contactor. 

 
9.

 

If 12V DC is not present when the booster pump is activated, trace yellow and yellow/black 
wires to TB-2 and measure the DC voltage at the terminals.  It should read 12V when activated. 

 
10.

 

If 12V DC is not present at the Booster Pump terminals, then disassemble Controller Enclosure 

and open the shell by removing 4 screws.  This exposes the main controller circuit board. 

 
11.

 

Confirm the “BOOSTER PUMP (BP)” LED, as shown in the Fig. 1, is on when the Booster 

Pump is activated.  Whenever this LED is on, BP terminals on the circuit board has 12V.  If it is 
not the case, replace the controller circuit board. 

 
12.

 

If the voltage is present but the Booster Pump Contactor does not activate, then check cable 

connections between the Controller Enclosure and Main Power Enclosure. 

 

Diversion Valve (3-Way Valve) Troubleshooting 

 

If the Diversion Valve fails to operate, follow these steps to isolate the problem. 

 

1.

 

Disassemble Controller Enclosure and open the shell by removing 4 screws.  This exposes 
the main controller circuit board. 

 
2.

 

Disconnect 3 wires from “SAL PROBE” terminals temporarily after noting wire 
connections.  (Main Printed Circuit “PC” Board)  This fools the controller to “think” there is 
good water. 

 
3.

 

Start the system. 

 
4.

 

Approximately 10 seconds after the system starts, the Water Quality LED turns green from 
red.  If this is not observed, then go to Salinity Level Calibration procedure. 

 
5.

 

When the Water Quality LED is illuminating in green, disconnect a control cable connector 
at the Diversion Valve.  If the solenoid inside of the valve is functioning, a distinct click 
sound is heard. 

Page I - 11 

Содержание Seafari Versatile SFC-1400-2



































































































































































Отзывы: