Horizon Reverse Osmosis Seafari Versatile SFC-1400-2 Скачать руководство пользователя страница 35

Страница: 35 / 162

HRO

Systems

Horizon

Seafari

“Section E” Installation

Page E - 3

Keep the product water tubing as straight and short
as possible.

Do Not Install Any Valves in this line. Blockage
of the Product Water Line causes extensive
damage to the System and the R.O. Membrane
Element.

G. UNCRATING:

DO NOT DISCARD ANY PACKAGING
MATERIAL UNTIL YOU HAVE FOUND AND
IDENTIFIED ALL PARTS!

Remove the Horizon Seafari system from the
shipping crate.

Some of the components are loose or separately
packaged in the shipping container.

Do Not

discard any packaging or boxes as they

may contain small mounting hardware pieces or
small system components.

H. HIGH PRESSURE PUMP PREPARATION:

1. Remove the orange shipping plug from the high-

pressure pump and replace with the orange, vented
cap.

It is very important that the vented cap is installed
or pressure builds up within the pump crankcase,
which may lead to pump damage

2. Ensure that the pump oil level is at the center of the

pump sight glass.

The pump oil must be filled with HRO Systems
supplied pump oil.

Location of Oil Sight Plug.

(Pump oil must be filled to middle of

glass prior to operation.)

Supplied Orange-Colored Vented

Oil Fill Cap Must Be Installed

Prior to Use.

Feed Water Inlet to High Pressure

Pump (From Pre-filter or Oil/Water

Separator)

High Pressure Hose

Connection (To R.O.

Membrane Inlet)

INSTALLATION

KIT

MODULAR SYSTEMS PACKAGED COMPONENTS

(NO OPTIONS SHOWN)

Pre-filters

Booster Pump

Main System

INSTALLATION

KIT

Pre-filters

Main System

Booster Pump

High-Pressure

Pump

Controller

Main Power

Enclosure

SELF-CONTAINED SYSTEMS PACKAGED COMPONENTS

(NO OPTIONS SHOWN)

Содержание Seafari Versatile SFC-1400-2



































































































































































Результаты поиска

Содержание Seafari Versatile SFC-1400-2

Отзывы:

Бренды по названию

Популярные бренды

Horizon Reverse Osmosis Seafari Versatile SFC-1400-2, Руководство пользователя

Результаты поиска

Содержание Seafari Versatile SFC-1400-2

Отзывы:

Бренды по названию

Популярные бренды