manualshive.com logo in svg

horiba JOBIN YVON SYNAPSE, Руководство пользователя

Поделиться
Скачать
horiba JOBIN YVON SYNAPSE Скачать руководство пользователя страница 81

Appendix C: Performing Routine Procedures with SynerJY 

 

71

Triggering  

Synapse detection systems offer both input and output TTL trigger functions. Triggering 
functions are software enabled. Two hardware triggers are available as SMB receptacles 
on the back of the controller: one for TTL input (male) and one for TTL output (female). 
Triggering can be activated at the start of each experiment or at the start of each 
acquisition during the course of one experiment. 
To enable triggering using SynerJY: 

1.

 

Start SynerJY and open the 

Experiment Setup

 screen. 

2. Select the 

Triggers 

tab. The Triggers window will open. 

 

3. From the 

Input Trigger

 heading, click 

Enable

 to activate the 

Input Trigger

. 

 

4.  Select the appropriate 

Input Trigger

 parameters. 

Event

 allows the user to specify 

whether the Trigger will be enabled once, at the start of the experiment or at the 

Содержание JOBIN YVON SYNAPSE





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды