manualshive.com logo in svg

horiba JOBIN YVON SYNAPSE, Руководство пользователя

Поделиться
Скачать
horiba JOBIN YVON SYNAPSE Скачать руководство пользователя страница 56

Detector System Component Description 

 

46

 

Best Dynamic Range Mode 

For low to medium light applications, where ratioing of photon peak information is 
crucial, the end-user is recommended to use the Best Dynamic Range gain setting.  This 
medium gain mode of operation allows end-users to have good sensitivity, as well as, the 
capability to collect larger photon levels without compromising linearity. 
It should also be noted that selection of this gain mode allows end-users with high light 
applications to acquire the same photon flux information four to six times faster 
(depending on the selected CCD) when compared to using the High Light gain setting 
mode. 

 

High Light Mode 

The High Light gain setting mode of operation enables the end-user to see the complete 
full well capability of the sensor, including the CCD’s transition from the linear to 
saturated region. 

 
 

Содержание JOBIN YVON SYNAPSE





















































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды