manualshive.com logo in svg

Honeywell SmartLine RM60, Руководство пользователя

Поделиться
Скачать
Honeywell SmartLine RM60 Скачать руководство пользователя страница 84

7

 SERVICE 

84 

SMARTLINE® RM60 (FMCW)

www.honeywell.com/ps

34-VF-25-31 iss.4 GLO December 15 US

7.5  Spare parts availability

The manufacturer adheres to the basic principle that functionally adequate spare parts for each 
device or each important accessory part will be kept available for a period of 3 years after 
delivery of the last production run for the device.

This regulation only applies to spare parts which are subject to wear and tear under normal 
operating conditions.

7.6  Availability of services

The manufacturer offers a range of services to support the customer after expiration of the 
warranty. These include repair, maintenance, technical support and training.

7.7  Returning the device to the manufacturer

7.7.1  General information

This device has been carefully manufactured and tested. If installed and operated in accordance 
with these operating instructions, it will rarely present any problems.

INFORMATION!

For more precise information, please contact your local sales office.

CAUTION!

Should you nevertheless need to return a device for inspection or repair, please pay strict 
attention to the following points:

•

Due to statutory regulations on environmental protection and safeguarding the health and 
safety of the personnel, the manufacturer may only handle, test and repair returned devices 
that have been in contact with products without risk to personnel and environment.

•

This means that the manufacturer can only service this device if it is accompanied by the 
following certificate (see next section) confirming that the device is safe to handle.

CAUTION!

If the device has been operated with toxic, caustic, flammable or water-endangering products, 
you are kindly requested:

•

to check and ensure, if necessary by rinsing or neutralising, that all cavities are free from 
such dangerous substances,

•

to enclose a certificate with the device confirming that is safe to handle and stating the 
product used.

Содержание SmartLine RM60

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды