manualshive.com logo in svg

Honeywell SmartLine RM60, Руководство пользователя

Поделиться
Скачать
Honeywell SmartLine RM60 Скачать руководство пользователя страница 105

 DESCRIPTION OF HART INTERFACE 

9

105

SMARTLINE® RM60 (FMCW)

www.honeywell.com/ps

34-VF-25-31 iss.4 GLO December 15 US

9.1  General description

The HART

®

 Protocol is an open digital communication protocol for industry. It is free to use by 

anyone. It is included in the software embedded in signal converters of HART-compatible 
devices.

There are 2 classes of devices which support the HART

®

 Protocol: operating devices and field 

devices. There are 2 classes of operating devices (Master): PC-supported workstations (Primary 
Master) and manual control units (Secondary Master). These can be used in control centres and 
other locations. HART

®

 field devices include sensors, converters and actuators. Field devices 

include 2-wire and 4-wire devices, and also intrinsically-safe versions for use in hazardous 
areas.

There are 2 primary operation modes for HART-compatible devices: point-to-point mode and 
multi-drop mode.

If the device is used in point-to-point mode, the HART

®

 Protocol uses the Bell 202 Frequency 

Shift Keying (FSK) standard to put a digital signal on top of the 4...20 mA signal. The connected 
device sends and receives digital signals that agree with the HART

®

 Protocol, and sends analog 

signals at the same time. Only 1 device can be connected to the signal cable.

If the device is used in multi-drop mode, the network only uses a digital signal that agrees with 
the HART

®

 Protocol. The loop current is set to 4 mA. You can connect a maximum of 15 devices 

to the signal cable.

An FSK or HART

®

 modem is included in field devices and manual control units. It is necessary to 

have an external modem for PC-supported workstations. The external modem is connected to 
the serial interface.

9.2  Software history

INFORMATION!

In the table below, "x" is a placeholder for possible multi-digit alphanumeric combinations, 
depending on the available version.

Release date

Devices

HART

®

Device Revision

DD Revision

2010-11

All revisions

1

1

Содержание SmartLine RM60

































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды