Honeywell SmartLine RM60 Скачать руководство пользователя страница 27

Страница: 27 / 128

INSTALLATION

SMARTLINE® RM60 (FMCW)

www.honeywell.com/ps

34-VF-25-31 iss.4 GLO December 15 US

If the antenna is smaller than the process connection:

•

Make sure the flange on the nozzle is level.

•

Make sure that you use the applicable gasket for the flange dimensions and the process.

•

Align the gasket correctly on the flange facing of the nozzle.

•

Lower the antenna carefully into the silo.

•

Tighten the flange bolts.

Refer to local rules and regulations for the correct torque to apply to the bolts.

Equipment needed:

•

3 mm Allen wrench (not supplied)

If the antenna is larger than the process connection:

•

Make sure the flange on the nozzle is level.

•

Remove the antenna locking screw from the part below the flange.

•

Remove the antenna from the part below the flange.

•

Align the gasket correctly on the flange facing of the nozzle.

•

Put the device carefully on the silo flange. Do not attach the device flange to the silo yet.

•

Attach the antenna to the device inside the tank. Go to the top of the tank.

•

Lift the device a small distance. Attach the antenna locking screw to the part below the flange.

Tighten the antenna locking screw.

•

Put the device carefully on the silo flange. Tighten the flange bolts.

Figure 3-9: How to attach the device if the antenna is larger than the process connection

WARNING!

If you attach the antenna in a closed space, make sure that there is a good airflow in the area.
Make sure that a person not in the silo can always hear you.

Содержание SmartLine RM60

































































































































Результаты поиска

Содержание SmartLine RM60

Отзывы:

Бренды по названию

Популярные бренды

Honeywell SmartLine RM60, Руководство пользователя

Результаты поиска

Содержание SmartLine RM60

Отзывы:

Бренды по названию

Популярные бренды