Honeywell Sensepoint XCD RTD Скачать руководство пользователя страница 35

Страница: 35 / 68

Sensepoint XCD RTD Technical Manual SPXCDHMRTEN Issue 1

11 General Maintenance

Honeywell Analytics recommends that gas detectors are tested and re-calibrated on a six-

monthly basis, or according to site practice. For Sensepoint Toxic sensors that are used

either directly with XCD RTD transmitter or remotely mounted in a separate junction box,

please refer to individual sensor manual for specific recommended calibration periods.

11.1 Operational Life

Typical life of a toxic gas sensor is dependant on the application, frequency and amount

of gas exposure. Under normal conditions (3 monthly visual inspection and 6 monthly test/

re-calibration), the XCD toxic sensors have an expected life equal to or greater than 24

months. The XCD Oxygen sensor has an expected life equal to or greater than 12 months.

Refer to section 12 for sensor replacement procedures.

WARNINGS

Access to the interior of the transmitter, when carrying out any work, must only be

conducted by trained personnel.

Before carrying out any work ensure local regulations and site procedures are followed.

Appropriate standards must be followed to maintain the overall certification of the sensor

and transmitter.

To reduce the risk of ignition of hazardous atmosphere, de-classify the area or disconnect

the equipment from the supply circuit before opening the transmitter enclosure. Keep

assembly tightly closed during operation.

Never attempt to open a junction box/enclosure or replace/refit the sensor in potentially

hazardous atmospheres.

Take care when handling sensors as they may contain corrosive solutions.

Do not tamper with or in any way disassemble the sensor.

Do not expose to temperatures outside the recommended ranges.

Do not expose sensors under storage conditions to organic solvents or flammable liquids.

At the end of their working life, replacement electrochemical sensors for oxygen and toxic

gas must be disposed of in an environmentally safe manner. Disposal should be according

to local waste management requirements and environmental legislation.

Alternatively, old replaceable sensors may be securely packaged and returned to Honeywell

Analytics clearly marked for environmental disposal.

Electrochemical sensors should NOT be incinerated as this action may cause the cell to

emit toxic fumes.

Caution: Oxygen deficient atmospheres (less than 6%V/V) may result in inaccuracy of

reading and performance.

Содержание Sensepoint XCD RTD





































































Результаты поиска

Содержание Sensepoint XCD RTD

Отзывы:

Похожие инструкции для Sensepoint XCD RTD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RTD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RTD

Отзывы:

Похожие инструкции для Sensepoint XCD RTD

Бренды по названию

Популярные бренды