Honeywell Sensepoint XCD RTD Скачать руководство пользователя страница 7

Страница: 7 / 68

Sensepoint XCD RTD Technical Manual SPXCDHMRTEN Issue 1

4.1 Transmitter

The transmitter enclosure has three threaded entries. The two M20 cable entries either

side of the upper part of the transmitter housing are for connecting the power source,

signal output and relay contacts to associated signalling equipment. The bottom M25 entry

allows local mounting of a Sensepoint Toxic sensor or cable entry when using a remotely

mounted sensor. There is a mounting plate incorporated into the transmitter housing

allowing for various mounting configuration options.

A local LCD provides gas type, concentration, alarm and operating status. The display

provides numerical, bar graph and icon information.

Diagnostic information may also be displayed when the transmitter is interrogated using

a magnet. The transmitter cover has a glass window which allows use of the Magnetic

Wand to activate the three user interface magnetic switches that are located on the front

of the display module. The magnet also enables a non intrusive, one-man calibration and

configuration facility for the Sensepoint XCD RTD.

4.2 Sensepoint Toxic Gas Sensor

The Sensepoint XCD RTD transmitter is designed to work with a range of Sensepoint

toxic sensors (see section 7 for details of gases and ranges available) .

Diagram 2: Sensepoint XCD RTD Display and Magnetic Switches

Measuring

Units

Inhibit Icon

Test Pass Icon

Warning/

Fault Icon

Magnetic Wand

activation Icon

Gas Type

Magnetic

MENU/ENTER

Switch

Magnetic

UP Switch

Magnetic

DOWN

Switch

Gas Reading

Bar Graph

Alarm Icon

Full Scale

Calibration Icon

XCD RTD

Содержание Sensepoint XCD RTD





































































Результаты поиска

Содержание Sensepoint XCD RTD

Отзывы:

Похожие инструкции для Sensepoint XCD RTD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RTD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RTD

Отзывы:

Похожие инструкции для Sensepoint XCD RTD

Бренды по названию

Популярные бренды