Honeywell Sensepoint XCD RTD Скачать руководство пользователя страница 20

Страница: 20 / 68

Sensepoint XCD RTD Technical Manual SPXCDHMRTEN Issue 1

7 Default configuration

The Sensepoint XCD transmitter is supplied with the following default configuration.

Function

Value/Setting

Meaning

Signal output

≥0.0<1.0 mA

Fault (refer to table 5 section 12.3 for details)

2.0 mA or 4.0 mA (17.4mA)

Inhibit (during configuration/user settings)

For Oxygen, 2.0 mA or 17.4 mA

4.0 mA to 20.0 mA

Normal gas measurement

22.0 mA

Maximum over range

Alarm Relay 1*

Value is sensor dependant

Lower alarm level

De-energized

Energizes on alarm

Contact Normally Open (NO)

Closes on alarm

Alarm Relay 2*

Value is sensor dependant

Higher alarm level

De-energized

Energizes on alarm

Contact Normally Open (NO)

Closes on alarm

Fault Relay

<1mA

Detector Fault

Energized

De-energizes on alarm

Contact Normally Open (NO)

Closes on alarm

Inhibit

2.0 mA (default) or 4.0 mA for Toxic

and Flammable

2.0 mA (default) or 17.4 mA

For Oxygen

Signal output inhibited during menu use.

If any relay is set to inhibit relay, then inhibit relay will

be activated.

Timeout

Disabled

No inhibit timeout. The detector waits for a button

press before returning to the previous state/setting.

Timeout period can be set in ‘Configure Inhibit’ menu

Configuration Mode

Password

0000 (Disabled)

0000 (Password disabled). If changed then password

is activated.

Location

(Tag Number)

0000

Optional feature to identify the location or User’s “Tag”

number of the XCD

Gas Type

Gas type must be set up manually during

commissioning, see section 9.1 for procedure

on how to set the Gas Type and measuring range of

the sensor to be used with Sensepoint XCD RTD.

Temperature

Option to have

C or

* Alarm relays automatically reset when reading falls within alarm thresholds. If relay configured to LATCH, then relays must be reset using

the Magnetic Wand.

Table 3: Default configuration

Содержание Sensepoint XCD RTD





































































Результаты поиска

Содержание Sensepoint XCD RTD

Отзывы:

Похожие инструкции для Sensepoint XCD RTD

Бренды по названию

Популярные бренды

Honeywell Sensepoint XCD RTD, Техническое руководство

Результаты поиска

Содержание Sensepoint XCD RTD

Отзывы:

Похожие инструкции для Sensepoint XCD RTD

Бренды по названию

Популярные бренды